WPM

Albert's Double Snow Blower in 1:12

Last Update: Jan. 9th, 2018

The company Bruder brought a snow blower (part no 02349) on the market in 2016, which is only a toy and not functioning at all. But it can serve as a low-cost base for a conversion and in the end yields an optical appealing snow blower. Some colleagues already did a conversion, and Klaus Bergdolt wrote about it in detail in the German magazine Truckmodell 2/2017. Motivated by his article I decided a conversion as well, but it should be a double snow blower which by chance fits perfectly to the width of my PistenBully model in 1:12. Klaus made the blower fan and housing out of thin sheet metal. As I don't have this specific knowledge and tools I designed the parts in CAD and had them printed.

My first version had a bevel gear box, which is quickly built, but has some disadvantages in regards to rotational speed of the drum and durability. Therefore I made a second version with a worm gear box. The necessary precise position of the gears is no problem with printed parts. I even went one step further and designed the entire center part new. This is now simply clipped in instead of the original center part. This makes the conversion easy even for not so skilled hobbyists.

The printed parts can be ordered at Shapeways at the Webshop of AT modellbau. A list of the required printed parts and also all other parts is a the bottom.


Warning: For enlarging the bore of the worm gear a lathe is absolutely necessary because this cannot be made reliably centric on a drill press.

The high speed rotating parts with the powerful motor represent a considerable risk of injury with improper handling and use.

We assume therefore expressively no liabilty for damage resulting from the reproduction or injury! The reconstruction is done at your own risk.

Disassembly
Gear Box and Bearings
Motor
Chimney
Double Snow Blower
Mounting to the Snow Cat
Video of the First Test Runs
List of all Required Parts


The German magazine Rad & Kette 1/2018 issued an article by me about building the double snow blower. It's in German language.

The article can be downloaded here as PDF, with friendly permission by the magazine


Disassembly

First the snow blower needs to be disassembled: the parts are connected by clips which can be opened by using a screw driver to push them apart. The clips of the drum end disks are not needed later, so I simply cut them off. After the drum has been disassembled the clipped in center part can be removed. I hollowed out the housing with my Proxxon Micromot tool and proper cutting and milling bits, see pictures:


Removing the rear cover with a sawing blade

Rear cover removed

Milling out the housing with a milling bit

Finishing with a sanding bit

The socket for the chimney is replaced by a roller bearing and a printed part and can thus be removed completely. The original center part will be replaced completely and can thus be disposed.

I created all needed parts in CAD with precise fit: blower housing with worm gear box, engine mount, blower fan, gear box cover, distance rings, chimney socket with sprocket and cover. I ordered them as Nylon laser sinter printing and already colored accordingly:

The correct position of the printed blower fan housing is guaranteed by the clipping it in. For optical reasons the rear edge of the clipped-in center part should be flush with the rear edge of the snow blower housing. Who wants to be on the safe side can glue the parts together, but only after a correct fit of the drum shaft has been achieved (see further down).


The opening for the chimney is enlarged such that it is flush with the chimney part of the blower housing, see picture to the left.


Gear Box and Bearings

I used a 6 mm aluminum round rod for the drum shaft. To install the two outer ball bearings to the snow blower housing reduction sleeves are necessary. These are available as printed parts, too. I glued these together with the ball bearings with super glue.

I had to extend the bore of the worm gear to 6 mm, and to make sure that it is absolutely centric I did this on the lathe with an inside cutting bit. 

For the gear box I pressed ball bearings 7x3 mm and 12x5 mm into the respective bearing positions. Also the gear box cover gets a ball bearing for the second bearing of the worm shaft. The worm shaft is mounted as shown in the photo. The shaft is 31 mm long. For fixation I used M3x3 worm screws. To position the gears I also used the ball bearings and made sure that the shaft is equally set back in both bearings.


Ball bearings in the gear box

Worm shaft 31 mm long (top with ball bearings)

To install the gear box cover M2 threads need to be tapped into the housing. For this pre-drill with a 1,5 mm drill bit with the cover in place. Afterwards the holes on the cover can be enlarged to 2 mm. Now the engine pinion can be put into place. A small bore is in the housing to tighten the worm screw on the motor pinion. Afterwards the worm shaft and finally the worm gear is put into position. Between worm gear and ball bearing a 1,2 mm washer needs to be inserted.
Don't forget to grease the gears well!


Pre-drilling with 1,5 mm

Installed gears


Motor

I used a relatively slow running and high torque brushless motor to drive the blower fan and drum. I designed the printed parts fitting for this specific motor. The shaft needs to be replaced by a longer shaft, which is fortunately possible with brushless motors. To remove the socket set screw I heated the shaft with a soldering iron to soften the thread locker. After removing the e-clip I could remove the shaft on the drill press by placing the housing on the machine vise and pressing down with a 3 mm shaft (of course with the drill switched off). I made a groove for the e-clip on the new longer 3 mm stainless steel shaft on the lathe. I also milled flat parts on the shaft for a better bite of the socket set screws for motor and sprocket. Then I screwed the motor to the printed part, and I used the flat head screws which come with the motor to install the blower fan (see photos):

Motor with extended shaft (77 mm long)
End disks with fitting hubs


Motor installed in the motor housing

Installed blower fans

 

I glued the drum spirals to each other. The left and right spirals can not be mixed up because the connections have either one or two inside teeth. Now the left and right drum have to be adjusted so that they fit exactly without any clearance. For this I carefully adjusted the end parts on the lathe. I fixed the drums with M2 flat head screws to the shaft, the screws going through the shaft. As they cannot be tightened a (removable) thread locker is absolutely necessary.

To attach the end disks I shortened their hubs and glued fitting turned aluminum hubs in place. The hubs have a M2 socket set screw. To ensure concentricity the turned hubs have to fit tightly and need to be pressed to the disks while glueing them with super glue.


Chimney

Following the recommendation of Klaus Bergdolt I enlarged the chimney to 25 mm to avoid possible snow block up. For the first version I enlarged the existing chimney myself, but for version 2 and the kit the enlarged chimney is available as a printed part. To change the throwing distance the black part of the original chimney is used.


Chimney as printed parts



Cartridge for mounting the chimney bearing

Chimney socket

Roller bearing for the chimney rotation

Chimney socket with gears

I carefully enlarged the throw out hole so that it is flush with the chimney part of the blower housing. A thin roller bearing with an inner diameter of 25 mm enables the chimney rotation. The adjustment is done by RC with a 1:100 motor gear box combination which is installed into the perfectly fitting housing. With the printed cartridge the ball bearing is positioned exactly in the correct position. The cartridge is glued to the chimney part of the blower housing and to the inner ring of the ball bearing.

The speed controllers for the chimney rotation are really small and they have the advantage that they can be plugged in directly to the receiver. Only wires with a servo plug have to be soldered to them (see picture below).

For version 2 I realized a simple RC adjusting of the throwing distance with a servo which is directly mounted to the chimney. I glued the 1 mm steel wire into the groove of the rod of the Bruder chimney. Of course this can be made nicer and hidden with a dummy hydraulic cylnder. Maybe I'll do this later.

The chimney socket is glued to the outer ring of the ball bearing, and finally the chimney is glued to the socket. Now the snow blower is ready for the first test run.


Speed controller for the chimney rotation

Servo for changing the throwing distance

 

Optional Instead of the Printed Chimney
The economical and technically skillful model builders can also extend the original chimney as I did it for the first version. With the Proxxon and the sawing blade I cut the chimney in half and enlarged it with a 7 mm wide strip of 1 mm Polystyrol sheet. I glued the parts with super glue. The sides were also enlarged with Polystyrol, see photos:


Enlarging the chimney sides

Widening the chimney to 25 mm

 


Double Snow Blower

To combine tow blowers to a double blower there are basically two versions:
- two separate single blowers (as I did it for version 1)
- combined blowers with a single center drum, like the original (my version 2)

Separate Single Blowers

This is the easier version. Two identical snow blowers are built, each with end disks on boht sides, which function completely indepent. With the mounting frame they are positioned side by side.


Double snow blower with two identical single blowers

 

Combined Snow Blowers with Single Center Drum

This version is realized at the original, the center drum is one piece. To built this as a model 3 Bruder blowers are needed, because one has to be a part donor.

Due to the self-locking worm drive the drum shaft has to be made of two pieces: the (in driving direction) left motor powers the left outer drum and the entire center drum. The right motor powers only the right outer drum. Therefore the right blower housing has an additional bearing mount as can be seen in the picture below. This housing must be to the right because only then both shafts are hold in position by the end disks and the worm gears and can thus not move.

To connect the housings I cut the drum mounts like shown in the lower right picture and fixed them with plenty of epoxy glue. The easiest way of filling the 7 mm wide gap is by using the special printed part (see part list at the bottom) which was designed by Constantin Woywod. Alternatively it can be made from parts of the 3rd Bruder blower. I glued both housings together and I additionally used bolts (lower left picture).


Double snow blower with single housing and center shaft

Connecting both housings with bolts

Cutting of the center pieces

One piece center drum

Glueing of the center drum
Two additional spiral pieces are needed for the center drum. That's why a 3rd Bruder blower ist needed. The picture below shows how the finished part looks like. To combine the spirals I sanded them accordingly and glued them together after I added a plastic washer to fill the gap of the shaft. The washer was made from no longer needed parts.



Mounting to the Snow Cat

To mount it to the snow cat I designed a frame in CAD based on the mounting frame which Westa is using for their double snow blowers. Eric made good photos a couple of years ago when he visited the Westa factory. I removed the bolts at the snow blower housing and drilled 3 mm holes in the exact center (see photo below). I attached the snow blower to the frame with M3 scews.
The lower screws of the engine mount have to be cut flush to the nut because otherwise they would not fit into the gaps of the mounting frame.
Finally the cables of the motors had to be extended, for which I used black silicone wires to make them look like hydraulic hoses.


Machined mounts on the housing

Aluminum angle profile to re-enforce the frame (only needed for the frame of the blower with a one piece center drum)

Of course I made the frame fitting to the Pistenking attachment carrier to make the mounting on the snow cat really easy. The multiple wires were bundled with zip ties and guided into the chassis. I'm using a separate battery for the blower motors.

Each snow blower weighs about 375 grams and both can still be easily lifted by the blade servo. The massive snow blower fits size wise quite well to my PistenBully 600 Polar.


Installed double snow blower


 

To mount a single blower to the Dickie PistenBully 600 I designed a fitting mounting frame as well. It can be simply clipped to the Dickie front attachmend carrier instead of the snow blade.


Dickie PistenBully (model by Michi Weiermair)


Mounting frame for the Dickie PB600

 

To mount a single blower to a Bruder tractor conversion kit by ML-Tec a fitting mounting frame is available as well (it was designed by Jonas Dietrich). With this a single blower can be mounted to a ML-Tec front hydraulics Art.-No.: ML-FH-100-01.


Tractor conversion with ML-Tec (Model by Jonas Dietrich)


Mounting frame for ML-Tec front hydraulics


Working in snow


First Test Run in Snow (Video)


List of All Required Parts

All given prices are approximated because prices may always change on short notice.

Printed Parts for a Single Snow Blower:

1x Blower Fan Housing
1x Blower Fan
1x Motor Housing
1x Gear Box Cover
1x Chimney Base
1x Sprocket
1x Chimney Bearing Base
1x Cover for Chimney Gears
1x Distance Ring for Ball Bearings
1x Hubs for the Side Discs
1x Chimney Top
1x Chimney 25 mm wide for manual adjustment or 1x Chimney with servo mount, 25 mm wide
1x Mounting Frame for Dickie PB600 (if the snow blower is installed to a Dickie PistenBully)
or
1x Mounting Frame for ML-Tec (if the snow blower is installed to a ML-Tec front hydraulics)
Total about € 200,00 plus shipping


Version 1 (links) aus 2 Einzelschleudern und Version 2 (rechts) mit durchgehendem Mittelteil

Printed Parts for a Double Snow Blower Consisting of Two Separate Blowers:

2x Blower Fan Housing
2x Blower Fan
2x Motor Housing
2x Gear Box Cover
2x Chimney Base
2x Sprocket
2x Chimney Bearing Base
2x Cover for Chimney Gears
2x Distance Ring for Ball Bearings
2x Hubs for the Side Discs
2x Chimney Top
2x Chimney 25 mm wide for manual adjustment or 1x Chimney with servo mount, 25 mm wide
1x Mounting Frame for Double Blower

Printed Parts for a Double Snow Blower with a one Piece Center Drum:

Attention: 3 Bruder Snow Blowers are needed!
1x Blower Fan Housing
1x Blower Fan Housing for Double Blower
2x Blower Fan
2x Motor Housing
2x Gear Box Cover
2x Chimney Base
2x Sprocket
2x Chimney Bearing Base
2x Cover for Chimney Gears
1x Distance Ring for Ball Bearings
1x Hubs for the Side Discs
2x Chimney Top
2x Chimney 25 mm wide for manual adjustment or 1x Chimney with servo mount, 25 mm wide
1x Mounting Frame for Double Blower with a one Piece Center Drum
1x Center Part for Double Blower

Mechanical Parts for a Single Blower:

These Parts can of course be purchased at other dealers as well. But it is important that the dimensions are the same, otherwise they will not fit into the printed parts.

At Conrad.de (or your local online Conrad webpage):
3x 295612 RC car ball bearing 6X12X4  - Bearings for the drum
3x 295426 RC car ball bearing 3X7X3  - Bearings for the motor shaft and worm gear shaft 
1x 197429 Deep groove ball bearing 61805 2Z   for the chimney base
1x 890265 Grub screw M3 3mm 20 Stück - Worm screws for the gears
1x Servo Cable (1x JR socket, 1x open end) for the ER100 speed controller for the chimney movement
Heat resistant cable black silicone cable for extending the motor cables (length as neeeded)
Total about € 31,00 plus shipping

At Maedler.de (or your local Maeder dealer):
1x 30001000 Worm Gear made of bronze, Module 0,5, 25 Teeth
1x 30000000 Standard Hollow Worm, Single Thread, Right Hand, Module 0,5
2x 26201400 Spur Gear, Brass, Module 0,7, 14 Teeth
Total about € 43,00 plus shipping

Von Hobbyking.com:
1x TURNIGY MULTISTAR 2216-800KV 14POLE MULTI-ROTOR OUTRUNNER V2
ATTENTION: This motor is available in a new version with a different upper end which does not fit into the blower fan. Please make sure to order version V2 which looks like in the picture to the right.
1x AFRO ESC 20AMP MULTI-ROTOR MOTOR SPEED CONTROLLER
1x Turnigy TGY-1440A Analog Servo for adjusting the throwing distance (optional), select the fitting chimney
Total about € 26,30 plus shipping


At www.taja-elektronik.de:
1x GM100 Gear Box Motor G100 wiht metal gears (fits exactly into the mount)
1x ER100 Speed Controller
Total about € 20,00 plus shipping

Additionally:
3 mm stainless steel round rod for the extension of the motor shaft (77 mm long) and for the worm gear shaft (31 mm)
6 mm aluminum round rod for the drum shaft, about 380 mm long
M3x10 Counter Sunk Screws for the motor housing (5 screws)
M3x5 Hexagon Bolts for mounting the motor (4 screws)
M1.6 Counter Sunk Screws for mounting the gear box motor for the chimney adjustment (2 screws)
Retaining Washers 2,3 mm for the extented motor shaft (1 piece)
M3 nuts, washers, spring washers

Mechanical Parts for a Double Snow Blower Consisting of Two Separate Blowers:

Twice the amount of all parts as listed above for a single snow blower, plus additionally:
M3x16 Hexagon Bolts to mount the blowers to the frame (10 screws)

Mechanical Parts for a Double Snow Blower with a one Piece Center Drum:

Twice the amount of all parts as listed above for a single snow blower, except:
5x 295612 RC-CAR KUGELLAGER 6X12X4  - Bearings drum shaft, here only 5 bearings are needed.
plus additionally:
M3x16 Hexagon Bolts to mount the blowers to the frame (10 screws)
Aluminum Angle 10x10x2, for re-enforcing the mounting frame for the double snow blower with a one piece center drum

 

Back to Overview of Models